Wine Cabinet

Tom Muellner sent in this beautiful wine cabinet. (This is my first attempt to update this blog from my Androit Tablet so let's see what happens! My apologies to Tom if this doesnt come out very well.)

My home shop consists of 4 Shopsmiths: two 10er's and two Mk5's. The age range is 1952 to 1986. One Mk5 is a "shortie' with a 510 table setup.

Why four? I suppose it's because I don't have room for more. What can I say? I'm a "Smith" junkie. Actually, that's usually how I bought them. Other than my original 10er that my dad bought new, all have been acquired in various stages of disrepair. All have been rebuilt by me.

In the process, I've gotten just about all the available accessories. I leave the 510 shortie set as a table saw with the jointer on the end, the 500 powers my bandsaw & is used mostly in horizontal boring or drill press mode, one 10er is mostly lathe or disk sander, and the other 10er is set up as a dado saw & has an extra table with a router mounted under it.

I do some converting or swapping modes from time to time, depending on my needs, but the default setup seems to serve me well.

This is a wine cabinet I built for my son using an old wood wine case as the focal point for bottles. Dados, miters, rabbets, complex operations...all done on the 10er & Mk5. Everything fits. How about that???
Inbox'>My home shop consists of 4 Shopsmiths: two 10er's and two Mk5's. The age range is 1952 to 1986. One Mk5 is a "shortie' with a 510 table setup.

Why four? I suppose it's because I don't have room for more. What can I say? I'm a "Smith" junkie. Actually, that's usually how I bought them. Other than my original 10er that my dad bought new, all have been acquired in various stages of disrepair. All have been rebuilt by me.

In the process, I've gotten just about all the available accessories. I leave the 510 shortie set as a table saw with the jointer on the end, the 500 powers my bandsaw & is used mostly in horizontal boring or drill press mode, one 10er is mostly lathe or disk sander, and the other 10er is set up as a dado saw & has an extra table with a router mounted under it.

I do some converting or swapping modes from time to time, depending on my needs, but the default setup seems to serve me well.

This is a wine cabinet I built for my son using an old wood wine case as the focal point for bottles. Dados, miters, rabbets, complex operations...all done on the 10er & Mk5. Everything fits. How about that???

Walnut Flag Case

Bill V. sent me this picture of a this flag case he built with his Shopsmith and SPTs.

Our woodworking club received a request for a triangular flag box.  I downloaded some "plans" which included dimensions but not angles, so I concluded that the apex angle was 90 deg. The legs are 20.250 inches and the bottom is 20 5/8 inches according to the plan. This meant that the lower interior angles had to be 45 deg (according to Mr. Euclid.) Two equal sides means two equal angles. The sum of all interior angles of a triangle add up to 180 Deg. 180 minus 90 equals 90 divided by two equals 45 for each lower angle interior. That meant that the two lower miters had to be cut to 22.5 Deg for the 45 deg angle but cutting them flat did not work. The interior 22.5 angle had to be cut with the piece held vertically using the fixture shown below.

 

Thanks, Bill!

Tom P. in Madison, Indiana sent in this beautiful entertainment center he built with his Shopsmith.

I've had a used Mark V since 2002. Since then I have made all my projects since. Attached is a entertainment center for my son and his family. I used the Shopsmith to make all aspects of this project. Most is made out of Cherry veneer with solid cherry facing. When I made the sliding shelves I realized that I didn't buy full extension slides, so I added a sliding shelf on top of another shelf. Basicly saying that when the main slide pulls out then stops, the upper shelf sllides out farther. You might be able to see it one of the pictures. Table saw portion of my Mark V is the component used most for this project.

Crib and Changing Table

It's been a while since I've had time to update the site, but I just received this submission from Jon and decided to go ahead and post it. Hopefully I can get back to regular updates soon.

This is the crib and changing table I built out of red oak for my first born back in July. It is my first try at woodworking and prior to this I had never used a table saw. I had also never heard of the Shopsmith Mark V before I stumbled upon one on craigslist.

As far as the various operations – I used the table saw to rip and crosscut all of the pieces, as well as cutting the tenons. The drill press mode was used for doing the mortises for all the slats and drilling holes for the hardware. The Horizontal boring configuration helped with the dowels that I used to put the headboard together.

Since making the crib I have been doing some other projects including lathe work. The fact that I already had the capability meant I didn’t have to worry about getting a new machine to try something new.

Thanks,
Jon

Jon, congrats to you and your wife for the birth of your first child! That is a fantastic first project and I hope it stays in your family for generations! Keep up the great work!